Skip to content

QCC badge parts list

The circuit boards of the Queen City Con 0x4 badge, and every part on the badge schematic (EasyEDA, "QCC 0x4 Badges" V1.0). Use it to repair a badge, or to fit a part that yours came without. For what each part does in use, see Use your QCC badge.

Applies to

Supporter and pyramid badges. Both follow this schematic, but they differ in shape and in which parts are fitted, so not every part below is on every badge. A pyramid badge's front corner LEDs are not on the schematic, so they are not listed here.

Circuit boards

The badges are built on custom circuit boards designed for the con: purple, with white artwork. The schematic gives the boards themselves no reference, so they are listed by name.

Board Notes
Supporter badge board The main board of a supporter badge, a rectangle with rounded corners and a lanyard slot.
Keyboard board The supporter badge's keyboard, a second custom board that mounts on standoffs over the battery and the ProMicro. It has its own microcontroller and a tactile switch for each key, and it works as a CardKB-compatible I2C keyboard through the main board's KEYBOARD connector. Its indicator LEDs are marked FN_ON, SYM_ON, SHIFT_ON and POWER, and it has its own headers marked SAOV2, ICSP and TTL_SERIAL. Its parts are not on the badge schematic, so they are not listed here.
Pyramid badge board A triangle about 156 mm along the base and 101 mm tall, with a lanyard slot near the top point. It follows the same schematic as the supporter badge board, with fewer parts fitted.

Main modules

Ref Part Notes
U1 ProMicro nRF52840 board, sold as nice!nano compatible The main controller, with the USB-C port.
U2 Ai-Thinker Ra-01SH LoRa module (SX1262)
RF1 Antenna connector The LoRa antenna attaches here. On a supporter badge it is a right-angle SMA jack at the board's edge.
OLED 128×64 OLED, I2C Pins GND, VCC, SCL, SDA. On supporter badges; added to some pyramid badges.
KEYBOARD Custom keyboard board, CardKB-compatible over I2C The keyboard board, under Circuit boards. On supporter badges.
GPS GPS module with patch antenna Not on every badge. The supporter badge carries a NEO-7M.

Transistors, diodes and LED

Ref Part Notes
Q1 2N7000 MOSFET Switches the GPS on and off.
Q2 2N7000 MOSFET Drives the message LED.
Q3 2N7000 MOSFET Drives the buzzer.
D1, D2 1N914 diode (1N914BTR) Let the battery feed the 3.3 V supply as a backup. The schematic marks them as a workaround for faulty ProMicro boards that won't start on battery power.
MSG_LED XL-502UGD LED The message LED. The schematic calls for a green LED, but a red one has been seen fitted here.

Resistors and capacitors

Ref Value Notes
R1, R2, R3 10 kΩ Hold Q1, Q2 and Q3 off.
R4 680 kΩ Battery voltage divider, upper.
R5 1 MΩ Battery voltage divider, lower.
R6 10 kΩ Pull-up for SW1.
R7 10 kΩ Pull-up for RESET.
R8 330 Ω Message LED.
C1 100 nF Filters the battery supply after the POWER switch.
C2 100 nF Debounces SW1.
C3 100 nF Debounces RESET.

Switches and buzzer

Ref Part Notes
POWER SK12D07VG4 slide switch Disconnects the battery.
MUTE SK12D07VG4 slide switch Cuts the buzzer. Not on every badge.
SW1 Tactile switch The user button, marked USR on a pyramid badge.
RESET 6×6 mm tactile switch (SH-6X6X5.5H-C5)
BZ1 4 kHz passive buzzer, 5×5 mm, surface mount Not on every badge. It must be a passive buzzer: the badge plays tunes on it, and an active buzzer can only make one fixed tone.

Connectors

Ref Part Notes
BATT Molex 53048-0210, 1.25 mm pitch, 2 pins The battery connector.
BATT2 PH2.0 2-pin footprint (WAFER-PH2.0-2PWB) An alternative position for a 2.0 mm battery connector.
KEYBOARD HY2.0 4-pin (BX-HY2.0-4PWZ) GND, VCC, SDA, SCL.
GPS 4-pin 2.54 mm header (PZ254V-11-04P) VCC, GPS RX, GPS TX, and a ground that Q1 switches.
SAO 2×3 2.54 mm add-on (SAO v2) header (PM2.54-2*3) 3.3 V, GND, SDA, SCL. Pins 5 and 6 are not connected.
GPIO33, GPIO34, GPIO38, GPIO39 Single-pin 2.54 mm header positions Spare ProMicro pins.
3v3, GND Pads The 3.3 V supply and ground.

The 3v3 pad, the SAO header and the KEYBOARD, GPS and OLED connectors all sit on the badge's 3.3 V supply. Never connect 5 V or a battery to them. Anything you power from them must run on 3.3 V.

Battery

A single-cell 3.7 V LiPo on BATT. Supporter badges came with a 3000 mAh cell, and other badges with a 2000 mAh cell.

Before you plug in a cell from another source, check the polarity at its plug with a meter. Makers do not all wire two-pin plugs of this size the same way, and a reversed cell can damage the badge.

Treat the cell as you would any LiPo: never puncture, crush or short it, stop using it if it swells, and charge it through the badge's USB-C port.

Back to Use your QCC badge.


Edit this page